Skip to content
SoilX

Real-time cone penetration test data: See in the office what the cone is measuring right now.

SoilX, based in Kiel, Germany, is software for cone penetration testing (CPT), drilling and ground investigation. Readings stream from the rig to the office and to your client while the test is running – manufacturer-independent, with verified cones and full traceability. Built for drilling contractors and geotechnical consultants across Germany, Austria, Switzerland and Europe; the Live CPT module is in field trial.

024681012140102030 GWL 2.40
Cone resistance qc in MPa over depth in m (sample data) 24.8 MPa at 14.6 m

The data is there.
Access is missing.

Between probe, machine, field book, cloud and analysis, there are several media breaks today. Each of them costs time — and some cost entire working days.

Measurement errors are noticed too late

Whether the probe, cables and measurement chain are working properly often only becomes apparent from unusual values — in the worst case after the sounding. What follows are queries, repeat measurements and additional trips to site.

Decisions wait for specialist staff

If a technical assessment is needed during a sounding, someone has to be on site — or the work waits. With several machines running at the same time, this is hardly possible to resolve.

Data is captured several times

Field book, machine file, file storage, database: the same information is transferred, renamed and entered again. The effort goes not into the technical assessment, but into the preparation beforehand.

Existing data remains an archive

CPTs and borehole logs from completed projects sit as files in folders. For a new project at the same location, they are practically impossible to find and to compare.

What sits side by side today

Sounding data, field books, laboratory results and machine data describe the same ground — without a common frame of reference. This is exactly where SoilX comes in: first the common reference, then the analysis.

Real-time cone penetration test data: how readings reach the office

Five benefits.
One connected system.

What changes on site, in the office and for the client when drilling rig, measurement chain, field data capture and data storage work together in one system.

Until now: Without an in-house engineer, the borehole goes unsupervised

One interface for all devices. Live data even without your own geotechnical engineer.

For drilling and CPT contractors

The RemoteBridge is designed as a manufacturer-neutral interface: drilling and CPT rigs from different manufacturers deliver their measured values live and in a uniform format — whichever device happens to be in use.

For drilling companies without their own geotechnical engineers, this becomes a real competitive advantage: an external geotechnical consultancy joins live when needed and provides expert supervision of the drilling without travelling to site. This allows you to offer services with expert supervision that previously required your own specialist staff.

Enabled by: Live CPT & RemoteBridgeCPT Link

Until now: “The cone is fine” – said, but never documented

Quality you can prove.

ConeCheck checks the cone and measurement chain before use and documents the result; Cone Management keeps the complete history of every cone. During drilling, a specialist follows the values and spots anomalies immediately — not only during the analysis. Documentation is created in a structured way at the rig. The result: fewer repeat measurements, fewer queries, and results that can be traced back to the measurement.

Enabled by: ConeCheckCone ManagementLive CPT & RemoteBridgeFeldPro App

Until now: At the rig, it takes experience new staff don’t have yet

Faster onboarding. Less specialist knowledge needed at the rig.

Guided input forms, a purpose-built soil description keyboard and voice input lead staff step by step through the field book and soil logging. If anything is unclear, the help chat or the remotely connected specialist can assist — directly during drilling. New employees learn on real jobs; the technical assessment remains with the experts.

Enabled by: FeldPro AppCPT Link

Until now: The client waits for the report

Your client can follow along live.

For clients

With their own access permission, the client follows the drilling in the browser — from anywhere, without travelling and without interfering with machine operation. Progress and measured values are visible at all times. This builds trust, shortens coordination and sets your offer apart from the competition.

Enabled by: Live CPT & RemoteBridge

Until now: The rig stands still until the engineer arrives

No waiting for specialist staff or data.

If a decision is needed during drilling, the specialist joins remotely at short notice instead of travelling to site. Machine and team do not have to wait. And by the end of the working day, the data is already in your cloud in structured form — without transfer, post-processing or sending.

Enabled by: Live CPT & RemoteBridgeData Cloud & Crawler

Only possible as a connected system.
SoilX provides it.

Individual solutions each cover one part: the device software the measurement, a cloud storage service the filing, the telephone the consultation. The five benefits only arise when all links work together, regardless of manufacturer. SoilX connects them in one system — from the checked probe to access for the client.

  1. Device connection for all manufacturers
  2. Checked measurement chain
  3. Live transmission and remote access
  4. Guided field data capture
  5. Your own cloud with access permissions

If one link is missing, the benefit is missing.

Current status: Live CPT is in field trial, the unified RemoteBridge integration of all modules is the next integration stage, FeldPro exists as an app prototype, and ConeCheck and Cone Management are in development. Details under Development status.

SoilX for drilling and CPT contractors

SoilX for geotechnical consultants

One system.
Four levels.

Field software and Customer Cloud perform different tasks but operate as one system: the measurement programs remain on the machine, and the cloud becomes the shared working interface.

Level 01

CPT machine

Acquisition of the original measured values directly on the machine. Depending on the application, Live CPT, MagnetoMonitor and ConeCheck run here.

Level 02

RemoteBridge

Unified transmission layer between machine and customer server – for sessions, measurement data and status. The fully unified integration of all modules is the next integration stage.

Level 03

Customer server

Customer-specific data storage, cloud modules, history and user access. Your measurement data stays in your own environment.

Level 04

Customer Cloud

One user interface for live view, analysis, management, quality assurance and documentation – for field and office alike.

For manufacturers. The architecture is designed to be manufacturer-neutral: machine-specific data sources are connected on the field side, and the cloud receives a unified data model. Safety-related functions – such as an automatic machine stop in the event of connection loss – are a separate manufacturer integration and are specified and tested separately for each device.

SoilX for manufacturers of drilling and CPT rigs

One project,
four soundings.

This is what project-based analysis looks like: select a sounding, switch between profile comparison, CPT curves and borehole log — and ask the same question in plain language. The values shown are technically plausible sample data.

Illustrative preview, sample data

Project, Soundings

Query in plain language Project context active

AI outputs are a working basis and must be checked by qualified staff

Cone penetration testing terms explained

The SoilX Customer Cloud.
One interface for field and office.

A unified customer interface connects measurement on the CPT machine, live transmission, quality assurance, history and analysis. Each module can be used on its own – the particular value is created by linking them.

Dashboard of the SoilX Customer Cloud with tiles for Live CPT, Magneto, ConeCheck, Cone Management, Knowledge, Projects, and Files and Reports
Draft design of the dashboard (German interface), sample projects, no customer data, Full-size image

Dashboard Prototype

The control centre of the Customer Cloud: live status, current measurements, projects, checks, verification cases and files on one page – without switching between different programs.

Live CPT Field trial

Transfers the ongoing cone penetration test from the machine to the cloud: depth, cone resistance qc, sleeve friction fs, friction ratio Rf, inclination and temperature, plus a live profile with Robertson (SBT) evaluation. Office and field see the same measurement.

Real-time cone penetration test data: how readings reach the office

Magneto (MagnetoMonitor) In development

Live evaluation of magnetic measurement data along the sounding depth. Two three-axis sensor sets supply six raw channels; gradient and signal changes are displayed in sync with depth, and anomalous sections are marked at their actual depth. Also in development: an interface to SENSYS, a PDF report generated on site and the Magneto ControlCenter, which lets one UXO specialist monitor up to four rigs at once.

Magnetometer CPT for UXO surveys

ConeCheck In development

Documented field check of the CPT cone and the measurement chain – before use, after unusual contact or between measurements. Zero values, drift and calibration reference are compared; the result is transferred to the cloud as a status and history entry.

Checking the CPT cone: ConeCheck and Cone Management

Cone Management In development

A digital life record for every CPT cone: deployments, ConeCheck inspections, calibration data, certificates and warnings such as ‘calibration due’ – consolidated instead of distributed across individual files.

Knowledge In development

The reference and verification base behind the Magneto evaluation. Cases are separated by origin – simulated, research, test field, field-verified – and stored traceably with probe type, calibration status and algorithm version.

Projects Prototype

The technical framework for each construction project: CPTs, magnetometer soundings, machines, operators, cones used, measurement history and documents in one project view.

Reports / QA In development

Turns measurement data into documented quality assurance: measurement reports, ConeCheck evidence, calibration information and review notes, without having to gather individual files.

Files Prototype

Central storage for measurements, reports, photos, videos and project documents – with a clear separation between unchanged original data and the analyses derived from it.

Clear limits. MagnetoMonitor is a development and assistance system: a magnetic anomaly is initially a signal anomaly, not automatically an unexploded ordnance item, and does not replace an expert clearance decision. ConeCheck supplements quality assurance between calibration intervals but does not replace any required calibration, certification or manufacturer inspection.

Complementary tools

Further components are available for mobile work, data import and queries.

CPT Link Available

Mobile work platform for live measurement, help chat, archive and queries – one app version for every customer server.

Data Cloud & Crawler Available

Detects new CPT and field files in your cloud and imports them into the database in a structured, project-based way.

GeoQuery Available

Project-based search, display and analysis of CPTs and borehole logs, in plain language if required.

AI Proxy & Cost Control Available

Central approval of AI use: access per customer, monthly limits, usage overview and logging.

FeldPro App & Server Module App prototype

A separate offering for window sampling and boreholes: digital capture of field books and soil logs – by voice input and with a purpose-built soil description keyboard.

Digital borehole logs from the rig

Flow Roadmap

Toolkit for your own queries, checks, notifications and document workflows, built from easy-to-understand technical building blocks.

Fewer media breaks,
less time spent searching.

Beyond the five benefits on site, work in the office changes too. How large the effect is depends on your workflows.

No duplicate data entry

Field documentation, cloud and database work together. Data needs to be transferred, searched for, renamed or re-entered less often.

Reuse existing data

CPTs and borehole logs no longer remain mere archive files. Search, comparison and AI functions make them usable for new projects and internal analyses.

Invest step by step

Not every company needs the complete system straight away. Individual modules can be introduced separately and connected later.

Adapt to existing workflows

The open architecture allows your own interfaces, data sources and functions. The aim is not to replace proven workflows, but to connect them in a meaningful way.

For context. Potential savings come mainly from fewer repeat measurements, fewer trips to site, less manual data transfer, faster project coordination and better use of existing data. How large they actually turn out to be depends on the workflow, the number of machines, the data volume and the chosen module scope — this is assessed together on the basis of a pilot phase.

SoilX for geotechnical consultants

Ground, drilling,
equipment technology.

Three perspectives on the same data — with different questions and a different view of the results.

Engineering consultancies, ground investigation institutes and geotechnical departments assess the ground, classify layers and derive parameters. For difficult decisions, you join at short notice during the sounding instead of being permanently on site. For the analysis, CPTs and borehole logs from the same environment are available for comparison — and because the original data stays in your own cloud, every value in the report can be traced back to the measurement.

  • Join live
  • Layer classification
  • Project comparison
  • Traceable reports

SoilX for geotechnical consultants

The measurement chain is checked before use, the values are tracked during the sounding, and field documentation is created directly on the device. Instead of transferring records after the job, the documentation is available in structured form at the end of the working day. If several UXO soundings are running at the same time, a specialist can follow their progress on a mobile device and intervene where needed instead of standing at every machine. Companies without their own geotechnical engineers bring in an external geotechnical consultancy live — and the client follows the drilling with their own access permission.

  • One interface for all devices
  • Bring in geotechnical engineers live
  • Access for clients
  • Check report in advance
  • Capture at the rig
  • Records without rework

SoilX for drilling and CPT contractors

Manufacturers of CPT rigs, dynamic probing and drilling rigs and the associated measurement technology: your equipment supplies the data, SoilX supplies the layer above it — live provision, structured storage and analysis, connected via open interfaces. The measurement technology remains yours. The mobile application remains neutral: server, user rights, company name and data are determined by the respective customer environment. Individual components can also be technically integrated into manufacturer or partner solutions.

  • Device connection
  • Open interfaces
  • Neutral app per customer server
  • Joint development

SoilX for manufacturers of drilling and CPT rigs

From the machine
to the documented measurement.

Eight interlocking steps – an example of a sounding with SoilX.

01

Select project and machine

The measurement is clearly assigned to a job and a device.

02

Prepare the measuring system

Depending on the task, Live CPT, MagnetoMonitor or ConeCheck; probe, cone and calibration information are assigned.

03

Measure live

The field software reads new measurement points and displays them immediately on the machine.

04

Synchronise

Depth, measured values, session and status are combined – for Magneto, the depth assignment is crucial.

05

Transfer

The RemoteBridge transfers the data to the customer server.

06

See it together

Dashboard and specialist modules show the current state; office and field work on the same measurement.

07

Complete the measurement

The session is archived unchanged; analyses remain distinguishable from it.

08

Check and learn

Checks, verifications and confirmed findings feed into the history, QA and Knowledge.

Real-time cone penetration test data: how readings reach the office

What is in place today
— and what is not.

The status of each component, set out openly. All product views on this page are illustrative previews with sample data.

Module status

  • Customer Cloud — dashboard, projects, filesPrototype
  • Live CPTField trial
  • CPT Link — mobile work platformAvailable
  • Data Cloud & CrawlerAvailable
  • GeoQueryAvailable
  • AI Proxy & Cost ControlAvailable
  • FeldPro App and Server ModuleApp prototype
  • Magneto (MagnetoMonitor)In development
  • ConeCheckIn development
  • Cone ManagementIn development
  • KnowledgeIn development
  • Reports / QAIn development
  • RemoteBridge — unified integration of all modulesNext stage
  • Flow — workflow toolkitRoadmap

Note on status. Parts of the overall architecture have been implemented; others – in particular the fully unified RemoteBridge integration of all modules – are the next integration stage. Interfaces, data formats and safety-related functions are specified in binding form and tested for each manufacturer and application.

AI as a tool — with clear limits

A central AI proxy separates the specialist application from the external AI service. Access, approvals, cost limits and usage logs are managed centrally. The data protection arrangements required are defined to suit the respective environment and the AI provider used.

  • Approvals per customerCentrally managed
  • Monthly cost limitsCentrally managed
  • Traceable usageLogged
  • AI can be switched off completelyAt any time

Automated analyses and AI outputs are a working basis. They do not replace expert review.

Enquire about a pilot partnership

Frequently asked questions
about SoilX.

Short, direct answers on functionality, device connection, data storage and development status. The answers are also provided as structured data.

What is SoilX?

SoilX is a modular software system for cone penetration testing (CPT), drilling and ground investigation. At its core is the SoilX Customer Cloud: it combines Live CPT, magnetometer evaluation, cone checks, cone management, projects, quality assurance and files in one interface – manufacturer-neutral, from the machine to the report.

How can I see the measurements live in the office?

The RemoteBridge transfers the readings from the rig to your customer server while the test is running. In the office you open the Customer Cloud in your browser and see depth, cone resistance, sleeve friction and the live profile as they are measured – without waiting for the file after the test. Live CPT is currently in field trial.

What is cone penetration testing (CPT)?

In cone penetration testing (CPT), a probe with a conical tip is pushed into the ground at a constant rate. Cone resistance and sleeve friction are measured continuously, and pore water pressure where required. From these, the stratification and bearing capacity of the ground can be derived.

Who is SoilX intended for?

SoilX is aimed at three groups: geotechnical consultancies and engineering departments, drilling and CPT contractors, and manufacturers of drilling and CPT rigs. All three work with the same measurement data, but ask different questions of the results.

Does SoilX work with equipment from different manufacturers?

Yes, SoilX is designed for this. Machine-specific data sources are connected on the field side; the cloud receives a unified data model. The unified RemoteBridge integration of all modules is the next integration stage; we will clarify with you directly which devices are already connected.

Can a geotechnical engineer supervise drilling remotely?

Yes. With SoilX, a geotechnical engineer follows the measured values live in the browser and can join at short notice when needed, without travelling to site. This also allows drilling companies without their own geotechnical engineers to offer services with expert supervision, for example together with an external geotechnical consultancy.

Can the client follow the drilling live?

Yes. With their own access permission, the client sees the progress and measured values of the drilling in the browser – from anywhere and without interfering with machine operation. The executing company decides which data the client sees.

What are Magneto and MagnetoMonitor?

MagnetoMonitor evaluates the magnetic measurement data of a magnetometer sounding live along the sounding depth. Two three-axis sensor sets supply six raw channels, from which the gradient and signal changes are displayed in sync with depth. The module is a development and assistance system: an anomaly is not automatically an unexploded ordnance item and does not replace an expert clearance decision.

Does ConeCheck replace calibration of the CPT cone?

No. ConeCheck is a documented field check between calibration intervals – before use, after unusual contact or between measurements. It supplements quality assurance but does not replace any required calibration, certification or manufacturer inspection.

Where is the measurement data stored?

On your customer server or in your own cloud. Unchanged original measurement data is stored separately from the analyses derived from it; this keeps the origin of every value traceable, and any later re-evaluation can be based on the original data.

How does SoilX support the training of staff?

Guided input forms, a purpose-built soil description keyboard and voice input lead staff step by step through the field book and soil logging. If anything is unclear, the help chat or a remotely connected specialist can assist. As a result, less specialist knowledge is needed at the rig; the technical assessment remains with the experts.

Which SoilX modules are available today?

CPT Link, Data Cloud & Crawler, GeoQuery and AI Proxy & Cost Control are available. Live CPT is in field trial; the dashboard, projects and files of the Customer Cloud exist as a prototype, FeldPro as an app prototype. Magneto, ConeCheck, Cone Management, Knowledge and Reports/QA are in development; the unified RemoteBridge integration is the next integration stage.

Does the AI in SoilX replace expert assessment?

No. Automated analyses and AI outputs are a working basis and must be checked by qualified staff. AI use runs through a central proxy with permissions, cost limits and logging, and can be switched off completely at any time.

Who provides operation and support?

Operation, infrastructure and support are provided by our IT partner schimanski IT, which has around 20 employees. This means we can also deliver and support larger projects.

How much does SoilX cost?

The price depends on the scope of modules, the number of devices and the data volume. The usual starting point is a pilot phase in which benefits and effort are assessed together. Please contact us directly to discuss this.

Cone penetration testing terms explained

The people
behind SoilX.

Three founders, three layers: field practice and software, IT infrastructure and metalwork.

  • Portrait of Stephan Heuer

    Stephan Heuer

    Managing Director

    More than six years in CPT operations as a certified cone penetration testing specialist, on onshore and marine construction sites, with solid experience in software development. At SoilX he develops and tests the software and leads the technical discussions with manufacturers and customers.

  • Portrait of Denis Schimanski

    Denis Schimanski

    Managing Director

    Managing director of schimanski IT. At SoilX he is responsible for the IT infrastructure and its secure operation.

  • Photo to follow

    Kai Vormelcher

    Co-founder

    Managing director of “Der Schlosser” Vormelcher in Kiel, a metalwork company certified to EN 1090.

Start with one module.
Expand at your own pace.

For an introduction, we first clarify which data sources and workflows you already have in place. This results in a suitable pilot scope — from a single field or data module to the connected live system.

Send us a short note on which measurement data you generate and what your analysis currently depends on. You will receive a technical assessment in return — not a quotation.

Address

SoilX
Göteborgring 86
24109 Kiel-Mettenhof

Contact persons

Stephan Heuer
Denis Schimanski